Tripp Lite SmartOnline SU5000XFMRT2U Bruksanvisning

Tripp Lite UPS SmartOnline SU5000XFMRT2U

Läs nedan 📖 manual på svenska för Tripp Lite SmartOnline SU5000XFMRT2U (16 sidor) i kategorin UPS. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/16
Owner’s Manual
SmartOnline® Series 5kVA
Isolation/Step-Down
Transformer Module
Models: SU5000XFMRT2U, SU5000XFMR2UTAA, SU5000XFMRT2U20
(Series Number: AGAC7168)
Not suitable for mobile applications.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved.
Important Safety Warnings 2
Mounting 2
Features 4
Service 4
Warranty and Product Registration 5
Español 6
Français 11
WARRANTY REGISTRATION
Register your product today and be
automatically entered to win an ISOBAR
surge protector in our monthly drawing!
www.tripplite.com/warranty
2
SAVE THESE INSTRUCTIONS.
This manual contains important instructions and warnings that should be followed during the installation and maintenance of
Tripp Lite SmartOnline transformer modules. Failure to heed these warnings may affect your warranty.
Transformer Location Warnings
Install your transformer module indoors, away from excess moisture or heat, direct sunlight, dust or conductive contaminants.
Install your transformer module in a structurally sound area. Your transformer is heavy; exercise care when moving or lifting the unit.
Only operate your transformer module at indoor temperatures between 32° F and 104° F (C and 40° C). For best results, maintain
indoor temperatures between 62° F and 84° F (17° C and 29° C).
For proper ventilation, leave adequate space around all sides of the transformer module.
Do not install the transformer module near magnetic storage media, as this may cause data corruption.
Equipment Connection Warnings
Installation should only be performed by qualified service personnel.
CAUTION: To reduce the risk of fire, connect only to a circuit provided with a 20A or 30A (based on input plug) branch circuit overcurrent
protection in accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1. Short circuit
backup protection overcurrent protection is provided by the building installation. Be sure to use the proper overcurrent protection for the
installation in accordance with the plug/equipment rating.
Be sure to provide a local disconnect device on any models that are permanently installed without a plug that is easily accessible.
Connect your transformer module's grounding terminal to a grounding electrode conductor.
Branch circuit protection must be provided by building installation.
Maintenance Warnings
Your transformer module does not require routine maintenance. Do not open it for routine maintenance. There are no user-serviceable
parts inside.
Medical Applications and Life Support Warning
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of
the life support equipment or to significantly affect its safety or effectiveness is not recommended.
Important Safety Warnings
Mounting (Rack)
Mount your equipment in either a 4-post or 2-post rack or rack enclosure.The user must determine the fitness of hardware and procedures
before mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your rack or rack enclosure.
The procedures described in this manual are for common rack and rack enclosure types and may not be appropriate for all applications.
WARNING!
Transformer modules are extremely heavy! Use caution while lifting and mounting! User must properly stabilize
the module while lifting and mounting!
4-Post Mounting
1 Connect the two segments of each shelf A using the included attached screws and
wing nuts B. Leave the screws slightly loose so that the shelves can be adjusted in
the next step.
1A
B
B
3
2 Adjust each shelf to fit your rack, then mount them in the lowest available space of
your rack with the screws, nuts and washers provided C. Note that the support ledges
should face inward. Tighten the wingnuts that connect the shelf segments D.
3 Attach mounting ears E to the front mounting holes of your equipment F using the
screws provided G. The ears should face forward.
4 Using an assistant, lift your equipment and slide it onto the mounting shelves. Attach
your equipment to the rack by passing the screws, nuts and washers
(user-provided) H through its mounting ears and into the rack rails.
The transformer module can be mounted in an upright tower position when used with optional base stands, sold separately by Tripp Lite
(model: 2-9USTAND). When installing a transformer module, place it between the power module and the battery module.
WARNING!
Transformer modules are extremely heavy! Use caution while lifting and mounting! User must properly stabilize
the module while lifting and mounting!
Mounting (Tower)
Mounting (Rack)
2-Post (Telecom) Mounting
To mount your equipment in a 2-post rack, you must purchase a Tripp Lite 2-Post Rack-Mount Installation Kit (model: 2POSTRMKITWM, sold
separately). See the Installation Kit's owner's manual for complete mounting instructions.
2
3
C
F
EG
4
H
D

Produktspecifikationer

Varumärke: Tripp Lite
Kategori: UPS
Modell: SmartOnline SU5000XFMRT2U

Behöver du hjälp?

Om du behöver hjälp med Tripp Lite SmartOnline SU5000XFMRT2U ställ en fråga nedan och andra användare kommer att svara dig




UPS Tripp Lite Manualer

UPS Manualer

Nyaste UPS Manualer