WyreStorm EX-35-H2-ARC Bruksanvisning
WyreStorm
AV extender
EX-35-H2-ARC
Läs nedan 📖 manual på svenska för WyreStorm EX-35-H2-ARC (3 sidor) i kategorin AV extender. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/3
18Gbps 4K HDR HDBaseT Extender with
True ARC and Audio Breakout
EX-35-H2-ARC Quickstart Guide
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-35-H2-ARC Quickstart Guide | 181012
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Basic Wiring Diagram
IMPORTANT! Installation Requirements
• Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
• Read through the section for important wiring Wiring and Connections
guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
In the Box
1x EX-35-H2-ARC Transmitter
1x EX-35-H2-ARC Receiver
1x 12V DC 3A Power Supply (US/EU/UK)
3x 3‐pin Screw Down Male Phoenix Connectors
1x IR Emitter
1x IR Receiver
4x Mounting Brackets (2x for TX | 2x for RX)
1x Quickstart Guide (this document)
HDMI HDMI
Audio Return
Channel
12V DC 3A
Power Supply
EX-35-H2-ARC Transmitter (TX) EX-35-H2-ARC Receiver (RX)
4K HLG Source
4K HDR Source
4K HDR HDMI Display
HDMI
HDMI
Audio Return
Channel
KEY
HDMI
HDBaseT
Power
Audio Return Channel
HDBaseT
Cat6/6a/7
Note: S/PDIF I/O also available for audio return
Note: Extender set may be powered by either the TX or RX.
Only one power supply is required.
AV Receiver
Front Panel (TX/RX) Rear Panel (TX/RX)
Power LED Solid: The receiver is powered On
Off: The receiver is powered Off
Status LED Flashing: The receiver is operating normally.
Off: The receiver is Not operating normally.
HDCP LED
Solid: HDCP content is present.
Flashing: HDCP content is not present.
Off: No signal.
LINK LED
Solid: Link to receiver has been established.
Flashing: Link to receiver has not been
established.
Source Audio Out Use this connection to send audio separate
from the HDMI connection to the RX.
Audio Return Input
Set the switch to ARC to receive audio from
the display via the HDMI connection.
Set the switch to S/PDIF In to receive audio
from the display via the S/PDI In connection.
Power In
5.5mm Screw Down Barrel Jack
Connect to the included 18V DC 1A power
supply to the transmitter or receiver. A power
supply is not required on the other end as it
will be powered using PoH..
HDBT In
HDBT Out
8-pin RJ-45 female
Connect the transmitters HDBT Out to
receivers HDBT In.
IR TX
IR RX
IR TX - 3.5mm (1/8in) Mono Jack: Connect
to the supplied IR emitter to control a local
device from the remote display location via
HDBaseT.
IR RX - 3.5mm (1/8in) Stereo Jack: Connect
to the supplied IR receiver to send IR to the
remote display location via HDBaseT.
See for more IR TX/RX Guidelines
information.
RS-232 1x RS-232: 3-pin Phoenix
HDMI In
HDMI Out
19-pin type A HDMI female
Supports HDMI and DVI/D with adapter
S/PDIF In/Out
S/PDIF Out on the TX transmits audio from
the RX received via HDBaseT.
S/PDIF In on the RX receives audio to be sent
to the TX via HDBaseT. Audio Return Input
switch must be set to S/PDIF in order for
audio to be transmitted.
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-35-H2-ARC Quickstart Guide | 181012
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
2 of 4
EX-35-H2-ARC Transmitter (TX)
EX-35-H2-ARC Receiver (RX)
A B C D E F
EX-35-H2-ARC Transmitter (TX)
EX-35-H2-ARC Receiver (RX)
A B C D E F
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the transmitter and receiving device.
• Verify that all HDMI and HDBaseT connections are not loose and are
functioning properly.
• Verify that the HDBaseT cable is properly terminated following EIA568B
standard.
• Verify that the output resolution of the source and display is supported by
this extender.
• Congure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control
• Verify that the IR and RS-232 cables are properly terminated following the
Wiring and Connections section.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-35-H2-ARC Quickstart Guide | 181012
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
3 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
IR TX/RX Guidelines
• Using WyreStorm infrared emitters and receivers is the best way to ensure
that most IR coding formats are transmitted and received by the NetworkHD
system. Other 3rd party emitters and receivers can be used; however, these
devices must operate in the same manner as the WyreStorm devices.
• Due to differences in IR across 3rd party control systems their IR ports
should never be connected directly to a NetworkHD system as an
incompatibility may exist. WyreStorm offers a cable that compensates for
voltage differences as well adjusts for differences in the pins used within the
port. Refer to the product page for more information.CAB-IR-LINK
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip: Anode
Sleeve: Cathode (IR Signal)
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
Tip:
Ring: IR Signal
+5V DC
Sleeve: Ground (GND)
RS-232 Wiring
The EX-35-H2-ARC uses a 3-pin RS-232 with no hardware ow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary from
device to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
3rd Party Device
Pin 1 TX (Transmit) > To > RX (Receive)--- ---
Pin 2 RX (Receive) > To > TX (Transmit)--- ---
Pin 3 G (Gro d) > To > G (Gro d)un --- --- un
WyreStorm Co ectornn
Audio Return Input
This receiver contains a switch that determines where the Audio Return is
received to be sent back to the transmitter. Set this switch based on the
connections being used to send and receive audio. Set the switch to ARC to receive audio from the
display via the HDMI connection.
Set the switch to S/PDIF In to receive audio from the
display via the S/PDI In connection.
Produktspecifikationer
| Varumärke: | WyreStorm |
| Kategori: | AV extender |
| Modell: | EX-35-H2-ARC |
Behöver du hjälp?
Om du behöver hjälp med WyreStorm EX-35-H2-ARC ställ en fråga nedan och andra användare kommer att svara dig
AV extender WyreStorm Manualer
24 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
16 September 2024
AV extender Manualer
- AV extender Philips
- AV extender Ag Neovo
- AV extender Allnet
- AV extender Nedis
- AV extender Eminent
- AV extender Manhattan
- AV extender Black Box
- AV extender Tripp Lite
- AV extender Vision
- AV extender DataVideo
- AV extender Techly
- AV extender Bogen
- AV extender Matrox
- AV extender Teufel
- AV extender Digitus
- AV extender Belkin
- AV extender LevelOne
- AV extender InFocus
- AV extender Planet
- AV extender Konig
- AV extender Marmitek
- AV extender Genexis
- AV extender ATen
- AV extender Kindermann
- AV extender Gefen
- AV extender Wentronic
- AV extender Peerless
- AV extender Dynaudio
- AV extender Adder
- AV extender Monoprice
- AV extender Crestron
- AV extender Smart-AVI
- AV extender StarTech.com
- AV extender SIIG
- AV extender IOGEAR
- AV extender Extron
- AV extender KanexPro
- AV extender Intelix
- AV extender ASSMANN Electronic
- AV extender Blustream
- AV extender Avocent
- AV extender Rose
- AV extender Intellinet
- AV extender Ebode
- AV extender Accell
- AV extender Schwaiger
- AV extender Ecler
- AV extender Rose Electronics
- AV extender Epcom
- AV extender Kramer
- AV extender CYP
- AV extender TV One
- AV extender SmartAVI
- AV extender IMG Stage Line
- AV extender Lindy
- AV extender Atlona
- AV extender Lightware
- AV extender Vivolink
- AV extender Approx
- AV extender SWIT
- AV extender Hall Research
- AV extender AMX
- AV extender Rocstor
- AV extender MuxLab
- AV extender Seco-Larm
- AV extender ConnectPro
- AV extender Kanex
- AV extender TechLogix Networx
- AV extender C2G
- AV extender SEADA
- AV extender Comprehensive
- AV extender PureLink
Nyaste AV extender Manualer
27 Oktober 2024
22 Oktober 2024
22 Oktober 2024
20 Oktober 2024
19 Oktober 2024
19 Oktober 2024
19 Oktober 2024
19 Oktober 2024
19 Oktober 2024
19 Oktober 2024