Atdec AD-WT-8060 Bruksanvisning
Atdec
Platt panelstöd
AD-WT-8060
Läs nedan 📖 manual på svenska för Atdec AD-WT-8060 (4 sidor) i kategorin Platt panelstöd. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/4
AD-WT-8060 Page 1 of 4
Installation Guide
AD-WT-8060
Tilt Wall Mount 8060
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total
weight of all equipment being mounted.
! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid
electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.
M-C
M6x30
Screw
(x4)
M-B
M6x14
Screw
(x4)
M-D
M8x30
Screw
(x4)
M-A
M5x14
Screw
(x4)
M-F
Multi
Washer
(x4)
M-G
Short
Spacer
(x8)
M-E
M8x50
Screw
(x4)
B
Display Bracket (left)
C
Display Bracket (right)
A
Wall Plate
D
Security Bar
M-H
Long
Spacer
(x8)
E
Hex Key
REQUIRED TOOLS
• Phillips head screwdriver
• Power drill
• Suitable drill bit
• Driver bit for selected
wall fasteners
• Stud nder
• Spirit level
• Socket wrench set
COMPONENT CHECKLIST
0 - 80kg
(0 - 176lb)
WEIGHT RANGE
NOTE:
! Wall Plate Mounting Fasteners are NOT supplied with Wall Mounts.
Professional installer to ensure correct Mounting Fastener type, location &
quantity to suit structure where Wall Mount is installed.
! ALWAYS use a washer between the chosen fastener and the wall plate.
! Mounting fasteners to be used as per manufacturers instructions, including
minimum engagement to achieve necessary performance.
AD-WT-8060 Page 2 of 4
12 3
3. Hook and Secure the Display onto the Wall Plate
NOTE:
Ensure level adjustment
screws are retracted prior
to mounting the display.
3.1. Angle the display and hook the Display
Brackets over the top of the Wall Plate.
This should be completed by two people.
NOTE:
• Choice and supply of appropriate wall plate fasteners is the
responsibility of the installer.
• Consult a preferred fastener supplier or a structural engineer
to select fasteners which are most appropriate for the weight
of the display and wall construction method.
• Wall plate be level. Verify using a quality spirit level tool.must
• On a Stud Wall or Drywall use a good quality Stud Finder to
position mounting fasteners in the centre of studs.
• On a Masonry Wall avoid positioning Wall Plate mounting
fasteners in a mortar join.
B
C
M-H (OPTIONAL)
SPACER HEIGHT (mm)
M-G (OPTIONAL)
M-A
M-B
M-C
M-D
M-E
(M5x14)
(M6x14)
(M6x30)
(M8x30)
(M8x50)
M-F
403530252015105
2. Attach the Display Brackets to the Display
3.2. DSlide Security Bar through the slots at the bottom of each
Display Bracket, ensuring the Security Bar sits to the rear of
the Wall Plate and the display cannot be lifted up and off the
Wall Plate.
3.3. (OPTIONAL) To prevent theft of the display, add a padlock to
the end of . Security Bar D
1. Mount the Wall Plate to the Wall
Slot Dimension
Ø9 x 55mm
*Fasteners shown are for example only
NOTE:
• Always use multi-washers M-F.
• Ensure the display brackets are
not loose and screws are not
forced too deep into the display.
• If spacers are needed, use the
shortest possible combination
between the display bracket and
the display.
AD-WT-8060 Page 3 of 4
Remove the black plastic caps
from Display Brackets and B C.
Tilt the display to the desired
viewing angle and tighten the
nuts using a suitable socket
wrench tool to lock the angle
in place.
NOTE:
Support display whilst adjusting tilt.
NOTE:
Support display whilst turning the level adjustment screws.
Level Adjustment Display Tilt
ADJUSTMENTS
If needed, carefully turn the
screws at the top of each
display bracket clockwise using
Hex Key to level the display. E
Produktspecifikationer
Varumärke: | Atdec |
Kategori: | Platt panelstöd |
Modell: | AD-WT-8060 |
Behöver du hjälp?
Om du behöver hjälp med Atdec AD-WT-8060 ställ en fråga nedan och andra användare kommer att svara dig
Platt panelstöd Atdec Manualer
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
7 December 2024
10 September 2024
Platt panelstöd Manualer
- Platt panelstöd Samsung
- Platt panelstöd HP
- Platt panelstöd Pioneer
- Platt panelstöd Abus
- Platt panelstöd Acco
- Platt panelstöd Hitachi
- Platt panelstöd SilverStone
- Platt panelstöd GPX
- Platt panelstöd Blaupunkt
- Platt panelstöd Manhattan
- Platt panelstöd Vision
- Platt panelstöd Kensington
- Platt panelstöd Nec
- Platt panelstöd Techly
- Platt panelstöd BlueBuilt
- Platt panelstöd Da-Lite
- Platt panelstöd Luxor
- Platt panelstöd Steren
- Platt panelstöd Iiyama
- Platt panelstöd Barkan
- Platt panelstöd Digitus
- Platt panelstöd Insignia
- Platt panelstöd Sanus
- Platt panelstöd Peerless-AV
- Platt panelstöd Vogels
- Platt panelstöd Fellowes
- Platt panelstöd Planar
- Platt panelstöd Sven
- Platt panelstöd Konig
- Platt panelstöd One For All
- Platt panelstöd Ematic
- Platt panelstöd Newstar
- Platt panelstöd Ewent
- Platt panelstöd HQ
- Platt panelstöd BakkerElkhuizen
- Platt panelstöd Ultimate
- Platt panelstöd Peerless
- Platt panelstöd Proaim
- Platt panelstöd Monoprice
- Platt panelstöd Chief
- Platt panelstöd Ergotron
- Platt panelstöd Gabor
- Platt panelstöd Konig & Meyer
- Platt panelstöd Premier
- Platt panelstöd StarTech.com
- Platt panelstöd SIIG
- Platt panelstöd Bell'O
- Platt panelstöd B-tech
- Platt panelstöd Speaka
- Platt panelstöd Crimson
- Platt panelstöd Kogan
- Platt panelstöd Schwaiger
- Platt panelstöd Premier Mounts
- Platt panelstöd Cabstone
- Platt panelstöd Elite Screens
- Platt panelstöd Kanto
- Platt panelstöd V7
- Platt panelstöd Bretford
- Platt panelstöd Unicol
- Platt panelstöd Anthro
- Platt panelstöd Equip
- Platt panelstöd Zaor
- Platt panelstöd Dataflex
- Platt panelstöd Multibrackets
- Platt panelstöd AMX
- Platt panelstöd Rocstor
- Platt panelstöd CTA Digital
- Platt panelstöd Amer
- Platt panelstöd SunBriteTV
- Platt panelstöd Avteq
- Platt panelstöd Walker Edison
- Platt panelstöd My Wall
- Platt panelstöd Mount-It!
- Platt panelstöd LTN Technologies
- Platt panelstöd Heckler
- Platt panelstöd Helder
Nyaste Platt panelstöd Manualer
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
10 December 2024
9 December 2024
9 December 2024
9 December 2024
7 December 2024