Elba ETM-E3690P Bruksanvisning
Läs nedan 📖 manual på svenska för Elba ETM-E3690P (1 sidor) i kategorin Kran. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/1
ETM-E3690P
1. An opening hole of 35mm diameter is required on sink top or work top (C) for installation of tap.
2. Slide the rubber O-ring (B) up to the base of tap (A).
3.Screw the flex hoses (H) up to the extension tube, then insert the tap through the hole of sink top or
worktop (C), and position the tap properly.
4.Slide the plastic fitting I (D) through the extension tube ,then slide the plastic fitting II (E) through the
sprayer hose and up to the plastic fitting I(D).
Important: ensure the opening of plastic fitting I (D) is close to threaded tube , and the sprayer hose
runs freely through the plastic fitting II (E).
5.Put the permanent seat(F) through the threaded tube , and tighten the fixing washer(G) securely.
Important: make sure the hose runs smoothly before tightened the fixing washer.
6.Connect the flex hoses (H) to the hot & cold water supply, and the sprayer hose to the threaded tube.
7. Adjusting the pull-out length of sprayer hose and fasten the weighing ball (I) with screws.
●Before installation, please ensure that the following
work conditions are adhered to:
-Water temperature between 0 C - 90 C˚ ˚
-Water pressure between 0.05MPa – 1.0MPa. Pressure
reducing valve is necessary if pressure exceeds 1.2MPa
-Avoid major pressure di erences between hot and cold ff
water supply
●Flush pipes thoroughly before and after installation to
ensure water supply is free of any debris.
●Inspect tap fitting and debugged to its best. Do not
attempt to disassemble fitting on your own.
●Use thread sealant tape (PTFE) on any screw joining
connections and ensure all joints are securely tightened.
A Tap body
B Rubber O ring
C Sink top or work
top
D Plastic fitting I
E Plastic fitting Ⅱ
F Permanent seat
G Fix ing washer
H Flex hose
I Weighing ball
J Rubber washer
for flexi hose
This . FIAMMA SDN. BHD. will not be held responsible for the use of superseded or voided specifications.
Fabricatoe must check for cut-out accuracy.
specification is subject to change without notice
Stainless Steel Mixer Tap
Produktspecifikationer
| Varumärke: | Elba |
| Kategori: | Kran |
| Modell: | ETM-E3690P |
Behöver du hjälp?
Om du behöver hjälp med Elba ETM-E3690P ställ en fråga nedan och andra användare kommer att svara dig
Kran Elba Manualer
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
Kran Manualer
- Kran IKEA
- Kran Etna
- Kran Inventum
- Kran Lamona
- Kran Smeg
- Kran KitchenAid
- Kran Teka
- Kran Miomare
- Kran Ernesto
- Kran Berg
- Kran CDA
- Kran Blanco
- Kran Grohe
- Kran Franke
- Kran Nodor
- Kran Delta
- Kran Schütte
- Kran Elkay
- Kran Caple
- Kran Quooker
- Kran ZLine
- Kran Hansgrohe
- Kran Lynx
- Kran Hotto
- Kran Empire
- Kran Moen
- Kran Aloni
- Kran WillieJan
- Kran Sani-Lav
- Kran Mizzo
- Kran Fala
- Kran Neo
- Kran Livarno Lux
- Kran Billi
- Kran Deante
- Kran Omnires
- Kran Zip
- Kran The Galley
- Kran Oras
- Kran Viidako
- Kran Curaqua
- Kran Waltec
- Kran Sussex
- Kran Fantini
- Kran Oliveri
- Kran Rogerseller
- Kran Axor
- Kran Gessi
- Kran Graff
- Kran Zurn
Nyaste Kran Manualer
6 Oktober 2024
3 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024
1 Oktober 2024