HP OfficeConnect OC20 Bruksanvisning

HP Router OfficeConnect OC20

Läs nedan 📖 manual på svenska för HP OfficeConnect OC20 (4 sidor) i kategorin Router. Denna guide var användbar för 22 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

OfficeConnect OC20

Access Point

Installation Guide

Rev 06 | March 2018 1

The OfficeConnect OC20 wireless access points (APs) support

IEEE802.11ac standards for high-performance WLAN, and are

equipped with two radios. Multiple-in, Multiple-output (MIMO)

technology allows these APs to deliver high-performance

802.11n 2.4 GHz and 802.11ac 5 GHz functionality, while also

supporting 802.11a/b/g wireless services.

The OC20 access points provide the following capabilities:

Wireless transceiver

IEEE 802.11a/b/g/n/ac operation as a wireless access point

or air monitor

Compatibility with IEEE 802.3af PoE

Centralized management configuration and upgrade

Integrated Bluetooth Low Energy (BLE) Radio

Package Contents

OC20 access point

Ceiling Rail Adapter (spare: AP-220-MNT-C1)

AP-220-MNT-W1W

Quick Start Guide

This device must be professionally installed and serviced

by a trained ACMP or similar HPE-certified technician.

HPE access points are classified as radio transmission

devices, and are subject to government regulations of the

host country. The network administrator(s) is/are

responsible for ensuring that configuration and operation

of this equipment is in compliance with their country’s

regulations. For complete list of approved channels in

your country, refer to the refer to the ArubaOS

Downloadable Regulatory Table Release Notes at http://

h20565.www2.hpe.com/hpsc/doc/public/

display?docId=a00026718en_us.

Inform your supplier if there are any incorrect, missing, or

damaged parts. If possible, retain the carton, including

the original packing materials. Use these materials to

repack and return the unit to the supplier if needed.

Software

OC20 Hardware Overview

Figure 1 Front

LEDs

The OC20 access points have two LEDs that indicate the system

and radio status of the device. These two LEDs can be

configured into three separate modes:

Normal mode (by default): See Table 1

Both LEDs off

Blink mode: Both LEDs blink green (synchronized)

Access points are radio transmission devices and are

subject to governmental regulation. Network

administrators responsible for the configuration and

operation of access points must comply with local

broadcast regulations. Specifically, access points must

use channel assignments appropriate to the location in

which the access point will be used.

Table 1 OC20 LEDs Status in Normal Mode

LED Color/State Meaning

System

Status

(Left)

Off Device powered off

Green-

Blinking

Device booting, not ready for use

Green- Solid Device ready for use, no restrictions

Green-

Flashing

Device ready for use, uplink negotiated in

sub optimal speed (<1Gbps)

Red- Solid System error condition

Radio

Status

(Right)

Off Device powered off, or both radios

disabled

Green- Solid Both radios enabled in access mode

Green-

Blinking

One radio enabled in access mode

Amber- Solid Both radios enabled in monitor mode

Amber-

Blinking

One radio enabled in monitor mode

Alternating Green: one radio in access mode

Amber: one radio in monitor mode

System Status

Radio Status

2OfficeConnect OC20 Access Point | Installation Guide

Figure 2 Back Panel

Console Port

The serial console port is located at the back of the OC20 and is

a 4-pin connector covered by a dust cover. An optional serial

adapter cable (AP-CBL-SER) is sold separately to connect the

AP to a serial terminal or a laptop for direct local management.

Ethernet Port

The OC20 access points are equipped with one 10/100/

1000Base-T (RJ-45) auto-sensing, MDI/MDX Ethernet port

(ENET0) for wired network connectivity. This port supports IEEE

802.3af Power over Ethernet (PoE), as a standard defined

Powered Device (PD) from a Power Sourcing Equipment (PSE)

such as a PoE midspan injector or network infrastructure that

supports PoE.

Kensington Lock Slot

The OC20 access points are equipped with a Kensington lock

slot for additional security.

Reset Button

To reset a OC20 access point to factory default settings:

1. Press and hold down the reset button using a small, narrow

object such as a paper clip while the OC20 access point is

not powered on (either via DC power or PoE.)

2. Connect the power supply (DC or PoE) to the OC20 access

point while the reset button is being held down.

3. Release the reset button on the OC20 access point after 15

seconds.

DC Power Socket

If PoE is not available, an optional AP-AC-12V30B power

adapter kit (sold separately) can be used to power the OC20

access points.

Additionally, a locally-sourced AC-to-DC adapter (or any DC

source) can be used to power this device, as long as it complies

with all applicable local regulatory requirements and the DC

interface meets the following specifications:

12 Vdc (+/- 5%) and at least 12W

Center-positive 2.1/5.5 mm circular plug, 9.5 mm length

Before You Begin

Pre-Installation Checklist

Before installing your OC20 access points, ensure that you have

the following:

Cat5E or better UTP cable of required length

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE)

source.

HPE Aruba AP-AC-12V30B power adapter kit (sold

separately)

Identifying Specific Installation Locations

You can mount the OC20 access point on the ceiling or a wall.

Use your RF plan or wireless deployment modeling tools to

determine the proper installation location(s). Each location

should be as close as possible to the center of the intended

coverage area and should be free from obstructions or obvious

sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should

have been accounted for during the planning phase and

adjusted for in your RF plan.

Identifying Known RF Absorbers, Reflectors

and Interference Sources

Identifying known RF absorbers, reflectors, and interference

sources while in the field during the installation phase is critical.

Make sure that these sources are taken into consideration when

you attach an access point to its fixed location. Examples of

sources that degrade RF performance include:

Cement and brick

Objects that contain water

Metal

Microwave ovens

Wireless phones and headsets

CONSOLE

ENET

12V 1A

350mA57V

Console Port

Ethernet Port DC Power Socket

Reset Button

Kensington

Lock Slot

FCC Statement: Improper termination of access points

installed in the United States configured to non-US model

controllers will be in violation of the FCC grant of

equipment authorization. Any such willful or intentional

violation may result in a requirement by the FCC for

immediate termination of operation and may be subject to

forfeiture (47 CFR 1.80).

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and

5 GHz bands.

Produit radio basse puissance pour réseau local opérant

sur les fréquences 2,4 GHz et 5 GHz.

Niedrigenergie-Funk-LAN-Produkt, das im 2,4-GHz- und

im 5-GHz-Band arbeitet.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz

e 5 GHz.

3OfficeConnect OC20 Access Point | Installation Guide

Installing the Access Point

The OC20 access point ships with a ceiling rail adapter and an

AP-220-MNT-W1W mount bracket. Additional ceiling or wall

mount kits are sold separately as accessories.

Using the Ceiling Rail Adapter

The included ceiling rail adapter can be used to attach the OC20

access point to a 9/16” or 15/16” ceiling rail.

1. Pull the necessary cables through a prepared hole in the

ceiling tile near where the access point will be placed.

2. Place the adapter against the back of the access point with

the adapter at an angle of approximately 30 degrees to the

tabs (see Figure 3).

3. Twist the adapter clockwise until it snaps into place in the

tabs (see Figure 3).

Figure 3 Attaching the Ceiling Rail Adapter to the AP

4. Hold the access point next to the ceiling tile rail with the

mounting slots at approximately a 30-degree angle to the

ceiling tile rail (see Figure 4 and Figure 5). Make sure that

any cable slack is above the ceiling tile.

5. Pushing toward the ceiling tile, rotate the access point

clockwise until the device clicks into place on the ceiling tile

rail.

Figure 4 Mounting the Access Point to a 15/16” ceiling rail

Figure 5 Mounting the Access Point to a 9/16” ceiling rail

Using the AP-220-MNT-W1W Bracket

The included AP-220-MNT-W1W bracket can be used to mount

the OC20 access point to a wall.

1. Begin by attaching the bracket to the wall as shown in Figure

6 or Figure 7.

a. Install any necessary wall anchors. Wall anchors are not

included in the package.

b. Align the screw holes in the bracket with the previously

installed anchors or demarcated screw points.

c. Insert the screws to secure the bracket. Screws are not

included in the package.

Figure 6 Attaching the Bracket to a Wall

Figure 7 Attaching the Bracket to a Wall (Alternate)

2. Attach the AP to the secured bracket as shown in Figure 8.

a. Align the AP with the bracket, placing the AP so that its

mounting tabs are at an angle of approximately 30

degrees to the bracket.

3. Pushing toward the wall, rotate the AP clockwise until it

clicks into place (see Figure 8).

Service to all Hewlett Packard Enterprise access points

should be performed by an AMCP certified technician or

similar.

The installer is responsible for securing the access point onto

the ceiling tile rail in accordance with the steps below. Failure

to properly install this product may result in physical injury

and/or damage to property.

AP-130_003

AP-130_006

Produktspecifikationer

Varumärke:	HP
Kategori:	Router
Modell:	OfficeConnect OC20
Vikt:	96 g
Strömförsörjning:	5
Gränssnitt:	SATA
Internera:	Ja
Vikt (imperialistisk):	0.21 lbs
HDD kapacitet:	80 GB
HDD rotationshastighet:	5400 RPM
Mått (B x D x H):	69.85 x 69.85 x 9.5 mm
HDD storlek:	2.5 "
Driftspänning:	5 V
Komponent för:	Notebook
Mått (B x D x H) (brittisk):	2.75 x 0.374 x 3.957 "
Storlek på lagringsenhetsbuffert:	8 MB
Genomsnittlig väntetid:	5.6 ms
Startström:	1 A
Söktid (skrivande):	13 ms
Söktid (läsning):	11 ms