Sonneman QB 7520 Bruksanvisning

Sonneman Lättnad QB 7520

Läs nedan 📖 manual på svenska för Sonneman QB 7520 (2 sidor) i kategorin Lättnad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
©2023 SONNEMAN - A Way of Light
Assembly Instructions
QB
Product Information
and Warnings
7520
Small Sconce
IMPORTANT
Always disconnect the power before installing or replacing
Luminaires and before cleaning or other maintenance.
Consult a qualied, licensed electrician to ensure correct branch
circuit conductor.
Consulter un électricien qualié pour vous assurer que les
conducteurs de la dérivation sont adéquats.
Please read all included assembly instructions and warnings carefully
before installation. Contact Customer Service if you have any
questions or concerns. Before installation, please confirm that the
fixture is compatible with your supply voltage and dimming system,
if present.
LEDs are highly sensitive electronic devices, and must be treated
with care. Do not open any factory sealed compartments, and avoid
touching the LEDs with your hands or any object.
Although all our fixtures are equipped with protective devices,
LED electronic systems are vulnerable to power surges and supply
variations. Do not install LED fixtures on the same circuit as any
motors, appliances, or HVAC systems.
Do not remove of bypass any LED Driver or Transformer that is
provided with the fixture, and do not replace or substitute with
another power supply.
Fixtures must be wired in parallel on independent leads; do not
"daisy chain" multiple fixtures together or wire them in series.
All factory-made splices and connections must remain intact. LED
circuits are carefully designed and built, and improper connections
may damage the fixture.
Any mounting hardware is provided for your convenience
and should be used with discretion. Always use the appropriate
hardware for the mounting surface.
Instructions D'Installation
Multiple U.S. and foreign patents pending.
Assembly Instructions
Fig. 1
A
C
G
E
B
D
Note: Fixture is for Remote Driver Installation only
1. Shut o power to the branch circuit.
2. The LED driver (A) must be installed in a remote and accessible location near the xture
in accordance with local electrical code.
a. Connect the LED drivers live wire (black) to the live supply wire.
b. Connect the LED drivers neutral wire (white) to the neutral supply wire.
c. Connect the LED driver's positive (+) output wire to the necessary length of red
wire (not included) to reach the xture (B) location.
d. Connect the LED driver's negative (-) output wire to the necessary length of black
wire (not included) to reach the xture location.
e. Drill a small 3/4" hole (C) in the wall behind the xture (B) and pull the low voltage
wires through the wall.
3. Attach the mounting plate (D) to the wall using mounting screws (F) and anchors (E).
For Wet Location Use: Fixture must be installed in the orientation shown and mounted
minimum 4' above the ground.
4. Connect xture red conductor to the LED driver positive (+) output wire and connect
the xture black conductor to the driver negative (-) output wire. Push connections back
through the hole in the wall.
5. Place xture over the mounting plate (D) and secure into place using set screws (G).
For Wet Location use: Place a small bead of silicone or waterproof caulk (not included)
around the perimeter of the xture (B) where it comes into contact with the wall.
6. Restore power to the xture.
Care Instructions:
Use a clean, dry cloth when dusting.
To protect the nish, avoid any harsh
abrasives or chemicals.
Note:
This xture is dimmable with Electronic Low Voltage
(Trailing-Edge), Incandescent (Leading-Edge), and 0-10V
type dimmers only.
F

Produktspecifikationer

Varumärke: Sonneman
Kategori: Lättnad
Modell: QB 7520

Behöver du hjälp?

Om du behöver hjälp med Sonneman QB 7520 ställ en fråga nedan och andra användare kommer att svara dig




Lättnad Sonneman Manualer

Lättnad Manualer

Nyaste Lättnad Manualer