Audiovox AS9233ST Bruksanvisning

Audiovox Säkerhet AS9233ST

Läs nedan 📖 manual på svenska för Audiovox AS9233ST (8 sidor) i kategorin Säkerhet. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

128-8604

1 of 8

Remote Start Alarm Keyless Entry

Upgrade System

Congratulations on your purchase of this automotive Remote Start / Alarm Keyless Entry

Upgrade System. This system is a state - of - the - art system is designed to arm and disarm

when it receives a lock or unlock command from your existing Factory Keyless Entry

Transmitter. Taking a few moments to read this manual will help to ensure that your vehicle

is protected at all times.

NOTE:

The system has the ability to beep the vehicle's horn, sound a siren, or both. Where a beep

or chirp is mentioned, consider either or both may sound.

Also All functions of the system will be controlled by the factory transmitter, including the start

sequence however for optimum range, it is suggested that the one button transmitter supplied

be used for starting, and unlocking while running under control of the the remote start.

ARMING THE SYSTEM: ( ACTIVE )

1. Turn the ignition key off, exit the vehicle, and close all doors.

2. Press and release the Lock button on the keychain transmitter.

3. The siren and or horn will beep one time, the parking lamps will flash one time,

and the LED found on the glass mounted receiver will begin to slowly flash, indicating that

the system is ARMED.

If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.

Simply close the opened entry point to provide full protection. If the siren "chirped"

three times, sometime after arming, the exclusive delayed dome light learn circuit

has been programmed and the system detected a open entry point after the

learned delay expired. Again, closing the hood, trunk, or doors will correct the

problem and you do not need to disarm the system to make the correction. If the

siren/horn did not sound when arming, then the chirps have been turned off, and

you should refer to the section titled “ ELIMINATING THE ARM / DISARM CHIRPS “

in this manual.

4. Any time the door lock switch in the vehicle is used to lock the doors while

the ignition key is turned off, the system will immediately arm. To lock the doors

after entering the vehicle, make sure the ignition key is switched on first.

Turning the ignition key on first will stop the system from arming.

ARMING THE SYSTEM: ( PASSIVE )

1. Turn the ignition key off, exit the vehicle, and close all doors.

2. The LED will begin to flash rapidly, indicating that the system

is automatically ( passively ) arming. As an added convenience, the 30

second automatic passive arming will not begin until all doors are closed,

allowing passengers to exit the vehicle at their convenience.

3. In 30 seconds, you will hear a single short chip from the siren, and the vehicle’s

parking lamps will flash one time, indicating that the system has ARMED. At

this time, the dash mounted PRLED will begin to flash slowly, providing a

visualindication that the system is fully armed.

4. It is possible to program the system, that when the alarm is allowed to

automatically passive arm, there will be a 15 second delay after a door is

opened before the alarm will sound. However, if the system is programmed

for instant trigger there will be no delay. Check with your installer for the setting

of this feature.

Model AS9233ST

OWNER’S MANUAL

128-8604

2 of 8

Page 2

IMPORTANT! When the system is programmed for passive arming, the system

will always arm, even when the keychain transmitter has not been used to

lock the doors.

When you leave the vehicle, and a door has been left opened, the system will arm

after 10 minutes. If you plan to vacuum the car, or if service work is being

performed, either leave the key in the ignition and switched to the on position,

or put the system into valet mode. If you do not do this, the system will arm in

10 minutes, and you may inadvertently trip the alarm.

PROTECTION WHILE THE SYSTEM IS ARMED :

1. Opening any door, hood, or trunk will cause the alarm to immediately sound.

The alarm will continue to sound for 30 seconds, then stop and

automatically rearm the vehicle. If the potential thief left a door opened, the

alarm will sound for three more 30 second cycles, then re - arm and ignore the

opened door zone.

2. Whenever the system is armed, the on glass receiver's LED indicator will

slowly flash. This serves as a visual deterrent to the potential thief. The LED

is a very low current bulb, and will not cause the vehicle’s battery to drain, even

when the vehicle is left unattended for extended periods.

3. Whenever the system is triggered, the vehicle’s parking lights will flash for the

30 second alarm cycle, attracting added visual attention to the vehicle.

4. Whenever the system is armed, the vehicle’s starter will be disabled. The

vehicle will not start.

DISARMING THE SYSTEM :

1. As you approach the vehicle, press and release the unlock button on the

keychain transmitter.

2. The siren and or horn will beep two times, the parking lamps will flash two

times,and the on glass receiver's LED will turn off, indicating that the

system is DISARMED. If the optional entry illumination feature has been

installed, the vehicle’s interior lights will turn on for 30 seconds, or until the

ignition key is turned on.

NOTE: If your system has been programmed for “ passive arming “, then it will

begin to re-arm immediately after disarming. This is indicated by a

rapid flashing of the on glass receiver's LED. Opening one of the

vehicle’s doors will suspend the passive arming process until all doors

have been closed, or until the ignition key has been turned on.

INTRUSION WARNING SIGNALS :

The system will inform you if an intrusion attempt has occurred while you were away from

the vehicle. If an intrusion attempt has occurred, the siren and or horn will beep four times

when the system is disarmed. The vehicle’s parking lights will also flash three times to indicate

an intrusion has occurred.

Enter the vehicle and observe the on glass receiver's LED for further information.

1. If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to a voltage sensing, light activated entry point, or

to an optional sensor that has been connected to zone 1.

2. If the LED is flashing two times...pause...two times...pause...etc., then an

intrusion attempt was made to the hood or trunk, or to an optional sensor that

has been connected to zone 2.

3. If the PRLED is flashing three times...pause...three times...pause...etc., then an

intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory, and will only be erased

when the ignition key is turned to the “ on “ position.

OPERATING THE EMERGENCY PANIC:

The buttons on your keychain transmitter will allow you to immediately activate the alarm in

emergency situations. To use the remote panic switch;

1. Press the unlock, then lock, then unlock buttons on your keychain transmitter

128-8604

3 of 8

within3 seconds. The alarm will immediately sound, and continue to sound for

30 seconds.

2. To stop the alarm before the 30 second cycle has expired, simply press

and release the unlock button on your keychain transmitter.

NOTE: If the factory system has a panic mode, it is suggested that the factory panic feature

be used instead of the PRO9233ST to prevent any potiential problem of turning off the panic

mode.

USING THE VALET SWITCH :

The valet switch allows you to temporarily bypass all alarm functions, eliminating the need

to hand your transmitter to parking attendants or garage mechanics. When the system is in

valet mode, all alarm functions are bypassed, however the remote panic feature and

remote door locks will remain operational. To use the valet mode, the system must first be

disarmed either by using your keychain transmitter, or by overriding the system as

explained in the Manual Override Section of this manual.

TO ENTER THE VALET MODE:

1. Disarm the unit by use of the factory transmitter or by use of the manual override

sequence.

2. Turn the ignition switch to the “On” position.

3. Press and hold the pushbutton switch found on the glass mounted receiver assembly

for 5 seconds, until the LED turns on, indicating valet mode has been successfully

entered.

TO EXIT VALET:

With the ignition switch in the on position, press and release the pushbutton switch one time

. The LED turns off indicating the valet mode has successfully been exited.

MANUALLY OVERRIDING YOUR SYSTEM:

USING SIMPLE VALET SWITCH MANUAL OVERRIDE

If your factory transmitter is lost, broken, or otherwise rendered inoperable your Security

System can be disarmed without the use of the keychain transmitter. This is necessary,

since you will need the ability to operate your vehicle if the transmitter is lost or its battery

fails. If your system has been selected for Valet Switch manual override as indicated on the

last page of this manual, to override the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and hold the valet pushbutton switch found on the glass

mounted receiver.

The alarm system will stop sounding and enter the (bypassed) mode. You can now start

and operate the vehicle normally.

Typically this override mode is used only if the transmitter has become inoperative.

USING CUSTOM CODE MANUAL OVERRIDE:

If your factory transmitter is lost, broken, or otherwise rendered inoperable, your system

can be overridden allowing operation of the vehicle. The manual override code is pre-

programmed at the factory to 11. This code can be changed by the operator to a more

familiar two digit number. Once you’ve become familiar with the system’s operation and

override procedure, we suggest you change the code for added security.

NOTE: The override procedure below describes use, assuming that the factory

preset code has not been changed and is still set to the factory default 11.

The on glass receiver's LED valet/override push button switch is used to enter the

tenths and units digits, pressing and releasing this button one time for each

digit required.

If your system has been selected for Custom Code manual override as indicated on the last

page of this manual, to bypass the alarm system; with a code of 11, follow the sequence

listed below:

1. The LED is flashing indicating the unit is armed, enter the vehicle, the siren

will sound, turn the ignition switch to the “on” position.

Page 3

Produktspecifikationer

Varumärke:	Audiovox
Kategori:	Säkerhet
Modell:	AS9233ST

Behöver du hjälp?

Om du behöver hjälp med Audiovox AS9233ST ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Säkerhet Audiovox Manualer

Audiovox AS9233ST Bruksanvisning

11 September 2024

Audiovox Prestige Platinum APS 686T Bruksanvisning

10 September 2024

Audiovox APS-45 Bruksanvisning

10 September 2024

Audiovox PRO-9056TW Pursuit Series Bruksanvisning

10 September 2024

Audiovox APS 675 Prestige Platinum Bruksanvisning

10 September 2024

Säkerhet Manualer

Nyaste Säkerhet Manualer

Honeywell Galaxy G3 Bruksanvisning

24 Oktober 2024

Abus fubw50020 Bruksanvisning

22 Oktober 2024

Honeywell HRGX85X Bruksanvisning

21 Oktober 2024

Alphatronics AlphaVision NG Bruksanvisning

20 Oktober 2024

Aritech SHATTERPRO 3 Bruksanvisning

20 Oktober 2024

Axis Camera Station S9001 Mk II Desktop Terminal Bruksanvisning

19 Oktober 2024

Eminent EM6511 Bruksanvisning

18 Oktober 2024

Eminent EM6104 Bruksanvisning

18 Oktober 2024

Hikvision DS-2CD2232 Bruksanvisning

18 Oktober 2024

NetworX NX-595E IP Communication Module Bruksanvisning

5 Oktober 2024